3‑Layer Peppermint Bark by Cyndiok

Home Forums Recipes 3‑Layer Peppermint Bark by Cyndiok

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #788
    S_Wirth
    Participant

      3-Layer Peppermint Bark

      Adapted from Bon Appétit, December 1998

      When you’re shopping for white chocolate, make sure that the words “cocoa butter” appear in the list of ingredients. I used Callebaut, which is a worthy splurge.

      Also, to crush the peppermints coarsely, Bon Appétit advises tapping the wrapped candies firmly with the bottom edge of an unopened 15- to 16-ounce can.

      17 oz. white chocolate, such as Callebaut, finely chopped
      30 red-and-white-striped hard peppermint candies, coarsely crushed
      7 oz. bittersweet chocolate, such as Ghirardelli 60%, finely chopped
      6 Tbsp. heavy cream
      ¾ tsp. peppermint extract

      Turn a large baking sheet upside down, and cover it securely with aluminum foil. Measure out and mark a 9- by 12-inch rectangle on the foil.

      Put the white chocolate in a metal (or other heatproof) bowl, and set it over a saucepan of barely simmering water. (Do not allow the bottom of the bowl to touch the water.) Stir occasionally until the chocolate is melted and smooth; if you take its temperature with a candy thermometer, it should register 110°F. Remove the chocolate from the heat. Pour 2/3 cup of it onto the rectangle on the foil. Using an icing spatula, spread the chocolate to fill the rectangle. Sprinkle with ¼ cup of the crushed peppermints. Chill until set, about 15 minutes.

      Meanwhile, combine the bittersweet chocolate, cream, and peppermint extract in a heavy medium saucepan. Warm over medium-low heat, stirring frequently, until the mixture is just melted and smooth. Cool to barely lukewarm, about 5 minutes. Then remove the baking sheet from the refrigerator, and pour the bittersweet chocolate mixture over the white chocolate rectangle. Using an icing spatula – make sure you cleaned it after using it for the white chocolate, above! – spread the bittersweet chocolate in an even layer. Chill until very cold and firm, about 25 minutes.

      Rewarm the remaining white chocolate over barely simmering water to 110°F. Working quickly, pour the white chocolate over the firm bittersweet layer, using your (again, clean) icing spatula to spread it to cover. Sprinkle with remaining crushed peppermints. Chill just until firm, about 20 minutes.

      Carefully lift the foil from the baking sheet onto a large cutting board. Trim away any ragged edges of the rectangle. (These are yours to nibble at, a little prize for your efforts.) Cut the bark crosswise into 2-inch-wide strips. Using metal spatula, slip the bark off of the foil and onto the cutting board. Cut each strip crosswise into 3 sections, and then cut each section diagonally into 2 triangles. Or, alternatively, just cut each strip into smaller pieces of whatever size you like. That’s what I did.

      Pack into an airtight container, with sheets of wax paper between layers of bark to prevent them from sticking to one another. Store in the refrigerator. Serve cold or, to emphasize the slight softness of the bittersweet layer, let stand at room temperature for 10 minutes before serving.

      Note: This bark will keep for up to 2 weeks, if not more. If you plan to pack it in a tin or baggie with other holiday sweets, be sure to wrap it separately in plastic wrap. Or maybe wax paper and then plastic wrap, so that it doesn’t sweat. If you left it naked, so to speak, to mix and mingle with other cookies or candies, everything might wind up tasting and smelling like peppermint.

      Yield: about 36 pieces, or more, if you cut them smaller

      Spread the word
    Viewing 1 post (of 1 total)
    • You must be logged in to reply to this topic.